Technicolor C2100T: Difference between revisions

From charlesreid1

No edit summary
No edit summary
Line 1: Line 1:
=Links=
Firmware download:
Firmware download:
* https://charlesreid1.com/centurylink/CTQ002-4.12.1.71.bin
* https://charlesreid1.com/centurylink/CTQ002-4.12.1.71.bin
Line 8: Line 11:


DSLReports forums: https://www.dslreports.com/forum/centurylink
DSLReports forums: https://www.dslreports.com/forum/centurylink
=Telnet=


Telnet access:
Telnet access:
Line 14: Line 19:
* Remote console
* Remote console
* Enable telnet from WAN or LAN
* Enable telnet from WAN or LAN
When logging in via telnet, I see this: BCM963268 Broadband Router
==Telnet Commands==
Logging in and typing a question mark for help shows all the available commands:
<pre>
> ?
?
help
logout
exit
quit
reboot
env_list
autodetect
adsl
xdslctl0
xdslctl1
loglevel
meminfo
dnsproxy
ping
voice
dect
wlctl
lanhosts
passwd
restoredefault
save
swversion
uptime
cfgupdate
swupdate
exitOnIdle
wan
igmp
imageServer
pm
led
wpsbtn
snoop_on
snoop_off
</pre>
These commands provide lots of information about the router. Here's a brief rundown:
* env_list - lists all environmental variables, including _PROD_SERIAL_NBR, _BOOTLOADER_VERSION, _WL0_WEPKEY_SERIAL, _WL0_WPAKEY_SERIAL, _WL0_PIN_SERIAL
* autodetect - sets parameters (start_delay, cycle_delay, ppp_attempts, dhcp_attempts) for router
* adsl - asymmetric digital subscriber line, faster data rates over copper phone lines than by using conventional VOIP modem
* xdslctl0 - not sure, but looks like another advanced command line interface, related to ADSL
* xdslctl1 - ditto
* meminfo - info about how much memory is being used
* dnsproxy - dumps info or stats (in my case, nothing printed out........)
* ping - works like normal ping, say ping IPADDR
* voice - this is basically the program that you use to interface with VOIP settings on the router. See below for detailed output.
* dect - dect is some kind of phone handset base station functionality. more of this SIP/phone/dialing stuff.
* wlctl - wireless LAN control program
* lanhosts
* passwd - duh, changes password
* restoredefault - duh, restores default factory settings
* save
* swversion
===Voice===
Here's the output for the voice command:
<pre>
> voice
Command syntax:
voice --help                      -  show the voice command syntax
voice show                        -  show the voice parameters
voice show stats                  -  show call statistics
voice start                      -  start the voice application
voice stop                        -  stop the voice application
voice save                        -  store voice params to flash
voice reboot                      -  restart the voice application
voice set <param> <arg1> <arg2>.. -  set a provisionable parameter
List of voice set params and args:
defaults        <None>                      - Default VoIP setup
boundIfname    <LAN|Any_WAN|(WAN IfName, e.g. nas_0_0_35)> - vodsl network interface
ipAddrFamily    <IPv4|IPv6>                - IP address family
pstnDialPlan    <pstn line#> <dialPlan>    - PSTN dial plan
pstnRouteRule  <pstn line#> <Auto|Voip|Line> - PSTN Route rule
pstnRouteData  <pstn line#> <line #|URL for VOIP> - PSTN Route data
locale          <srvPrv#> <region>          - 2 or 3 character code
DTMFMethod      <srvPrv#> <InBand|RFC2833|SIPInfo> - DTMF digit passing method
hookFlashMethod <srvPrv#> <SIPInfo|None>    - Hook flash method
transport      <srvPrv#> <UDP|TCP|TLS>    - transport protocol
srtpOption      <srvPrv#> <Mandatory|Optional|Disabled> - SRTP usage option
regRetryInt    <srvPrv#> <seconds>        - SIP register retryinterval
regExpires      <srvPrv#> <seconds>        - Register expires hdr val
rtpDSCPMark    <srvPrv#> <mark>            - RTP outgoing DSCP mark
logServer      <srvPrv#> <hostName|IP>    - Log server
logPort        <srvPrv#> <port>            - Log server port
digitMap        <srvPrv#> <digitmap>        - dial digit map
T38            <srvPrv#> on|off            - enable/disable T38
V18            <srvPrv#> on|off            - enable/disable V.18 detection
reg            <srvPrv#> <hostName|IP>    - SIP registrar server
regPort        <srvPrv#> <port>            - SIP registrar server port
proxy          <srvPrv#> <hostName|IP>    - SIP proxy server
proxyPort      <srvPrv#> <port>            - SIP proxy server port
obProx          <srvPrv#> <hostName|IP>    - SIP outbound proxy
obProxPort      <srvPrv#> <port>            - SIP outbound proxy port
sipDomain      <srvPrv#> <CPE_domainName>  - SIP user agent domain
sipPort        <srvPrv#> <port>            - SIP user agent port
sipDSCPMark    <srvPrv#> <mark>            - SIP outgoing DSCP mark
musicServer    <srvPrv#> <hostName|IP>    - SIP music server
musicSrvPort    <srvPrv#> <port>            - SIP music server port
tagMatching    <srvPrv#> <on|off>          - SIP to tag matching
timerB          <srvPrv#> <time in ms>      - SIP protocol B timer
timerF          <srvPrv#> <time in ms>      - SIP protocol F timer
lineStatus      <srvPrv#> <accnt#> <on|off> - Activate line
physEndpt      <srvPrv#> <accnt#> <id>    - Phys Endpt
extension      <srvPrv#> <accnt#> <URI>    - SIP extension
dispName        <srvPrv#> <accnt#> <Name>  - SIP Display Name
authName        <srvPrv#> <accnt#> <name>  - SIP auth name
authPwd        <srvPrv#> <accnt#> <pwd>    - SIP auth password
MWIEnable      <srvPrv#> <accnt#> <on|off> - Msg Waiting Indication
cfwdNum        <srvPrv#> <accnt#> <number> - call forward number
cfwdAll        <srvPrv#> <accnt#> <on|off> - call forward all
cfwdNoAns      <srvPrv#> <accnt#> <on|off> - call forward no answer
cfwdBusy        <srvPrv#> <accnt#> <on|off> - call forward busy
callWait        <srvPrv#> <accnt#> <on|off> - call waiting
anonBlck        <srvPrv#> <accnt#> <on|off> - Anonymous call rcv blcking
anonCall        <srvPrv#> <accnt#> <on|off> - Anonymous outgng calls
DND            <srvPrv#> <accnt#> <on|off> - do not disturb
CCBS            <srvPrv#> <accnt#> <on|off> - Call completion on busy
speedDial      <srvPrv#> <accnt#> <on|off> - Speed dial
warmLine        <srvPrv#> <accnt#> <on|off> - Warm line
warmLineNum    <srvPrv#> <accnt#> <number> - Warm line number
callBarring    <srvPrv#> <accnt#> <on|off> - Call barring
callBarrPin    <srvPrv#> <accnt#> <number> - Call barring pin
callBarrDigMap  <srvPrv#> <accnt#> <digitmap> - Call barring digit map
netPrivacy      <srvPrv#> <accnt#> <on|off> - Network privacy
vmwi            <srvPrv#> <accnt#> <on|off> - Visual message waiting indication
vad            <srvPrv#> <accnt#> <on|off> - enable vad
pTime          <srvPrv#> <accnt#> <pTime>  - packetization period
codecList      <srvPrv#> <accnt#> <codec(1)[,codec(2)]> - codec priority list
rxGain          <srvPrv#> <accnt#> <rxGain> - rxGain (dB)
txGain          <srvPrv#> <accnt#> <txGain> - txGain (dB)
</pre>
Now trying voice show to show values of parameters:
<pre>
> voice show
Global Parameters:
------------------
BoundIfName          : Any_WAN
IP address family    : IPv4
Vodsl logLevel      : Error
Management Protocol  : TR69
Service Provider 0:
--------------------
  Associated Voice Profile: 1
  Locale                  : USA
  DTMFMethod              : RFC2833
  HookFlashMethod        : None
  DigitMap                : #xx|[2-9]11|1[2-9]11|[2-9]xxxxxxxxx|1[2-9]xxxxxxxxx|x.T
  Log Server Addr        :
  Log Server Port        : 0
  T38                    : on
  V18                    : off
  RTPDSCPMark            : 46
  SIP:
      Domain              :
      Port                : 0
      Transport            : UDP
      RegExpires          : 0
      RegRetryInterval    : 0
      DSCPMark            : 40
      Registrar Addr      :
      Registrar Port      : 0
      Proxy Addr          :
      Proxy Port          : 0
      OutBoundProxy Addr  :
      OutBoundProxy Port  : 0
      Music Server Addr    :
      Music Server Port    : 0
      To Tag Matching      : On
      Timer B ( in ms )    : 32000
      Timer F ( in ms )    : 32000
      SRTP Usage Option    : Optional
  Account 0:
  -----------
      ActivationStatus        : Disabled
      VoipServiceStatus      : Disabled
      CallStatus              : Idle
      Associated CM Acnt      : 0
      PhysEndpt              : 1
      Extension              :
      DisplayName            :
      AuthName                :
      AuthPwd                :
      TxGain                  : 0 dB
      RxGain                  : 0 dB
      CALLFEATURES:
        MWI                  : off
        CallWaiting          : on
        CFWDNum              :
        CallFwdAll          : off
        CallFwdBusy          : off
        CallFwdNoans        : off
        AnonymousOutgoingCall: off
        AnonymousCallRcvBlock: off
        DoNotDisturb        : off
        CallCompOnBusy      : off
        SpeedDial            : off
        WarmLine            : off
        WarmLineNum          :
        CallBarring          : off
        CallBarringMode      : None
        CallBarringPin      : 9999
        CallBarringDigitMap  :
        NetPrivacy          : off
        VMWI                : off
      CODECSETTINGS:
        VAD                  : off
        pTime                : 20
        CodecList            : (0) G.722
                                (1) G.711MuLaw
                                (2) T38
                                (3) NTE
  Account 1:
  -----------
      ActivationStatus        : Disabled
      VoipServiceStatus      : Disabled
      CallStatus              : Idle
      Associated CM Acnt      : 1
      PhysEndpt              : 1
      Extension              :
      DisplayName            :
      AuthName                :
      AuthPwd                :
      TxGain                  : 0 dB
      RxGain                  : 0 dB
      CALLFEATURES:
        MWI                  : off
        CallWaiting          : on
        CFWDNum              :
        CallFwdAll          : off
        CallFwdBusy          : off
        CallFwdNoans        : off
        AnonymousOutgoingCall: off
        AnonymousCallRcvBlock: off
        DoNotDisturb        : off
        CallCompOnBusy      : off
        SpeedDial            : off
        WarmLine            : off
        WarmLineNum          :
        CallBarring          : off
        CallBarringMode      : None
        CallBarringPin      : 9999
        CallBarringDigitMap  :
        NetPrivacy          : off
        VMWI                : off
      CODECSETTINGS:
        VAD                  : off
        pTime                : 20
        CodecList            : (0) G.722
                                (1) G.711MuLaw
                                (2) T38
                                (3) NTE
</pre>
===wlctl===
<pre>
> wlctl
Usage: wlctl [-a|i <adapter>] [-h] [-d|u|x] <command> [arguments]
  -h        this message and command descriptions
  -h [cmd]  command description for cmd
  -a, -i    adapter name or number
  -d        output format signed integer
  -u        output format unsigned integer
  -x        output format hexdecimal
ver    get version information
cmds    generate a short list of available commands
up      reinitialize and mark adapter up (operational)
down    reset and mark adapter down (disabled)
out    mark adapter down but do not reset hardware(disabled)
        On dualband cards, cards must be bandlocked before use.
clk    set board clock state. return error for set_clk attempt if the driver is not down
        0: clock off
        1: clock on
restart Restart driver.  Driver must already be down.
reboot  Reboot platform
radio  Set the radio on or off.
        "on" or "off"
dump    Give suboption "list" to list various suboptions
srclear Clears first 'len' bytes of the srom, len in decimal or hex
        Usage: srclear <len>
srdump  print contents of SPROM to stdout
srwrite Write the srom: srwrite byteoffset value
srcrc  Get the CRC for input binary file
ciswrite
        Write specified <file> to the SDIO CIS source (either SROM or OTP)
cisupdate
        Write a hex byte stream to specified byte offset to the CIS source (either SROM or OTP)
--preview option allows you to review the update without committing it
        <byte offset> <hex byte stream> [--preview]
cisdump Display the content of the SDIO CIS source
        -b <file> -- also write raw bytes to <file>
        <len> -- optional count of bytes to display (must be even)
cis_source
        Display which source is used for the SDIO CIS
cisconvert
        Print CIS tuple for given name=value pair
rdvar  Read a named variable to the srom
wrvar  Write a named variable to the srom
nvram_source
        Display which source is used for nvram
nvram_dump
        print nvram variables to stdout
nvset  set an nvram variable
        name=value (no spaces around '=')
nvget  get the value of an nvram variable
nvram_get
        get the value of an nvram variable
revinfo get hardware revision information
customvar1
        print the value of customvar1 in hex format
msglevel
        set driver console debugging message bitvector
        type 'wl msglevel ?' for values
phymsglevel
        set phy debugging message bitvector
        type 'wl phymsglevel ?' for values
PM      set driver power management mode:
        0: CAM (constantly awake)
        1: PS  (power-save)
        2: FAST PS mode
wake    set driver power-save mode sleep state:
        0: core-managed
        1: awake
promisc set promiscuous mode ethernet address reception
        0 - disable
        1 - enable
monitor set monitor mode
        0 - disable
        1 - enable active monitor mode (interface still operates)
frag    Deprecated. Use fragthresh.
rts    Deprecated. Use rtsthresh.
cwmin  Set the cwmin.  (integer [1, 255])
cwmax  Set the cwmax.  (integer [256, 2047])
srl    Set the short retry limit.  (integer [1, 255])
lrl    Set the long retry limit.  (integer [1, 255])
rate    force a fixed rate:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate
mrate  force a fixed multicast rate:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate
a_rate  force a fixed rate for the A PHY:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate
a_mrate force a fixed multicast rate for the A PHY:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate
bg_rate force a fixed rate for the B/G PHY:
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate
bg_mrate
        force a fixed multicast rate for the B/G PHY:
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate
infra  Set Infrastructure mode: 0 (IBSS) or 1 (Infra BSS)
ap      Set AP mode: 0 (STA) or 1 (AP)
bssid  Get the BSSID value, error if STA and not associated
bssmax  get number of BSSes
channel Set the channel:
        valid channels for 802.11b/g (2.4GHz band) are 1 through 14
        valid channels for 802.11a  (5 GHz band) are:
                36, 40, 44, 48, 52, 56, 60, 64,
                100, 104, 108, 112, 116,120, 124, 128, 132, 136, 140,
                149, 153, 157, 161,
                184, 188, 192, 196, 200, 204, 208, 212, 216
cur_mcsset
        Get the current mcs set
chanspecs
        Get all the valid chanspecs (default: all within current locale):
        -b band (5(a) or 2(b/g))
        -w bandwidth, 10,20 or 40
        [-c country_abbrev]
chanspec
        Set <channel>[a,b][n][u,l]
        channel number (0-224)
        band a=5G, b=2G, default to 2G if channel <= 14
        bandwidth, n=10, none for 20 & 40
        ctl sideband, l=lower, u=upper
OR Set channel with legacy format:
        -c channel number (0-224)
        -b band (5(a) or 2(b/g))
        -w bandwidth, 10,20 or 40
        -s ctl sideband, -1=lower, 0=none, 1=upper
dfs_channel_forced
        Set <channel>[a,b][n][u,l]
        channel number (0-224)
        band a=5G, b=2G, default to 2G if channel <= 14
        bandwidth, n=10, non for 20 & 40
        ctl sideband, l=lower, u=upper
tssi    Get the tssi value from radio
txpwr  Set tx power in milliwatts.  Range [1, 84].
txpwr1  Set tx power in in various units. Choose one of (default: dbm):
        -d dbm units
        -q quarter dbm units
        -m milliwatt units
Can be combined with:
        -o turn on override to disable regulatory and other limitations
Use wl txpwr -1 to restore defaults
txpathpwr
        Turn the tx path power on or off on 2050 radios
txpwrlimit
        Return current tx power limit
powerindex
        Set the transmit power for A band(0-63).
        -1 - default value
atten  Set the transmit attenuation for B band. Args: bb radio txctl1.
        auto to revert to automatic control
        manual to supspend automatic control
phyreg  Get/Set a phy register:
        offset [ value ] [ band ]
radioreg
        Get/Set a radio register:
        offset [ value ] [ band/core ]
HTPHY:
        Get a radio register: wl radioreg [ offset ] [ cr0/cr1/cr2 ]
        Set a radio register: wl radioreg [ offset ] [ value ] [ cr0/cr1/cr2/all ]
ucflags Get/Set ucode flags 1, 2, 3(16 bits each)
        offset [ value ] [ band ]
shmem  Get/Set a shared memory location:
        offset [ value ] [band ]
macreg  Get/Set any mac registers(include IHR and SB):
        macreg offset size[2,4] [ value ] [ band ]
ucantdiv
        Enable/disable ucode antenna diversity (1/0 or on/off)
gpioout Set any GPIO pins to any value. Use with caution as GPIOs would be assigned to chipcommon
        Usage: gpiomask gpioval
devpath print device path
jtagureg
        g/set JTAG user registers
coma    Put the router in a catatonic state
pllreset
        set the pll to reset value
        Usage: wl pllreset
pcieserdesreg
        g/set SERDES registers: dev offset [val]
ampdu_activate_test
        actiate
ampdu_tid
        enable/disable per-tid ampdu; usage: wl ampdu_tid <tid> [0/1]
ampdu_retry_limit_tid
        Set per-tid ampdu retry limit; usage: wl ampdu_retry_limit_tid <tid> [0~31]
ampdu_rr_retry_limit_tid
        Set per-tid ampdu regular rate retry limit; usage: wl ampdu_rr_retry_limit_tid <tid> [0~31]
ampdu_send_addba
        send addba to specified ea-tid; usage: wl ampdu_send_addba <tid> <ea>
ampdu_send_delba
        send delba to specified ea-tid; usage: wl ampdu_send_delba <tid> <ea>
ampdu_clear_dump
        clear ampdu counters
dpt_deny
        adds/removes ea to dpt deny list
        usage: wl dpt_deny <add,remove> <ea>
dpt_endpoint
        creates/updates/deletes dpt endpoint for ea
        usage: wl dpt_endpoint <create, update, delete> <ea>
dpt_pmk sets DPT pre-shared key
dpt_fname
        sets/gets DPT friendly name
dpt_list
        gets status of all dpt peers
actframe
        Send a Vendor specific Action frame to a channel
        usage: wl actframe <Dest Mac Addr> <data> channel dwell-time <BSSID>
antdiv  Set antenna diversity for rx
        0 - force use of antenna 0
        1 - force use of antenna 1
        3 - automatic selection of antenna diversity
txant  Set the transmit antenna
        0 - force use of antenna 0
        1 - force use of antenna 1
        3 - use the RX antenna selection that was in force during
            the most recently received good PLCP header
plcphdr Set the plcp header.
        "long" or "auto" or "debug"
phytype Get phy type
rateparam
        set driver rate selection tunables
        arg 1: tunable id
        arg 2: tunable value
wepstatus
        Set or Get WEP status
        wepstatus [on|off]
primary_key
        Set or get index of primary key
addwep  Set an encryption key.  The key must be 5, 13 or 16 bytes long, or
        10, 26, 32, or 64 hex digits long.  The encryption algorithm is
        automatically selected based on the key size. keytype is accepted
        only when key length is 16 bytes/32 hex digits and specifies
        whether AES-OCB or AES-CCM encryption is used. Default is ccm.
        WAPI is selected if key len is 32 and arguments contain wapi.
        addwep <keyindex> <keydata> [ocb | ccm | wapi] [notx] [xx:xx:xx:xx:xx:xx]
rmwep  Remove the encryption key at the specified key index.
keys    Prints a list of the current WEP keys
tsc    Print Tx Sequence Couter for key at specified key index.
wsec_test
        Generate wsec errors
        wsec_test <test_type> <keyindex|xx:xx:xx:xx:xx:xx>
        type 'wl wsec_test ?' for test_types
tkip_countermeasures
        Enable or disable TKIP countermeasures (TKIP-enabled AP only)
        0 - disable
        1 - enable
wsec_restrict
        Drop unencrypted packets if WSEC is enabled
        0 - disable
        1 - enable
eap    restrict traffic to 802.1X packets until 802.1X authorization succeeds
        0 - disable
        1 - enable
cur_etheraddr
        Get/set the current hw address
perm_etheraddr
        Get the permanent address from NVRAM
authorize
        restrict traffic to 802.1X packets until 802.1X authorization succeeds
deauthorize
        do not restrict traffic to 802.1X packets until 802.1X authorization succeeds
deauthenticate
        deauthenticate a STA from the AP with optional reason code (AP ONLY)
wsec    wireless security bit vector
        1 - WEP enabled
        2 - TKIP enabled
        4 - AES enabled
        8 - WSEC in software
        0x80 - FIPS enabled
        0x100 - WAPI enabled
auth    set/get 802.11 authentication type. 0 = OpenSystem, 1= SharedKey, 2=Open/Shared
wpa_auth
        Bitvector of WPA authorization modes:
        1      WPA-NONE
        2      WPA-802.1X/WPA-Professional
        4      WPA-PSK/WPA-Personal
        64      WPA2-802.1X/WPA2-Professional
        128    WPA2-PSK/WPA2-Personal
        0      disable WPA
wpa_cap set/get 802.11i RSN capabilities
set_pmk Set passphrase for PMK in driver-resident supplicant.
scan    Initiate a scan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST  [active|passive|prohibit] scan type
        --bss_type=BT          [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC    particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N      number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N      dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan
iscan_s Initiate an incremental scan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST  [active|passive|prohibit] scan type
        --bss_type=BT          [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC    particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N      number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N      dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan
iscan_c Continue an incremental scan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST  [active|passive|prohibit] scan type
        --bss_type=BT          [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC    particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N      number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N      dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan
scancache_clear
        clear the scan cache
escan  Start an escan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST  [active|passive|prohibit] scan type
        --bss_type=BT          [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC    particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N      number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N      dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan
escanabort
        Abort an escan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST  [active|passive|prohibit] scan type
        --bss_type=BT          [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC    particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N      number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N      dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan
passive Puts scan engine into passive mode
regulatory
        Get/Set regulatory domain mode (802.11d). Driver must be down.
spect  Get/Set 802.11h Spectrum Management mode.
        0 - Off
        1 - Loose interpretation of 11h spec - may join non-11h APs
        2 - Strict interpretation of 11h spec - may not join non-11h APs
        3 - Disable 11h and enable 11d
        4 - Loose interpretation of 11h+d spec - may join non-11h APs
scanabort
        Abort a scan.
scanresults
        Return results from last scan.
iscanresults
        Return results from last iscan. Specify a buflen (max 8188)
        to artificially limit the size of the results buffer.
        iscanresults [buflen]
assoc  Print information about current network association.
        (also known as "status")
status  Print information about current network association.
        (also known as "assoc")
disassoc
        Disassociate from the current BSS/IBSS.
channels
        Return valid channels for the current settings.
channels_in_country
        Return valid channels for the country specified.
        Arg 1 is the country abbreviation
        Arg 2 is the band(a or b)
curpower
        Return current tx power settings.
        -q (quiet): estimated power only.
curppr  Return current tx power per rate offset.
txinstpwr
        Return tx power based on instant TSSI
scansuppress
        Suppress all scans for testing.
        0 - allow scans
        1 - suppress scans
evm    Start an EVM test on the given channel, or stop EVM test.
        Arg 1 is channel number 1-14, or "off" or 0 to stop the test.
        Arg 2 is optional rate (1, 2, 5.5 or 11)
rateset Returns or sets the supported and basic rateset, (b) indicates basic
        With no args, returns the rateset. Args are
        rateset "default" | "all" | <arbitrary rateset> -m <arbitrary mcsset>
                default - driver defaults
                all - all rates are basic rates
                arbitrary rateset - list of rates
                arbitrary mcsset - list of mcs rates octets, each bit representing
                                corresponding mcs
        List of rates are in Mbps and each rate is optionally followed
        by "(b)" or "b" for a Basic rate. Example: 1(b) 2b 5.5 11
        At least one rate must be Basic for a legal rateset.
roam_trigger
        Get or Set the roam trigger RSSI threshold:
        Get: roam_trigger [a|b]
        Set: roam_trigger <integer> [a|b|all]
        integer -  0: default
                    1: optimize bandwidth
                    2: optimize distance
            [-1, -99]: dBm trigger value
roam_delta
        Set the roam candidate qualification delta. roam_delta [integer [, a/b]]
roam_scan_period
        Set the roam candidate qualification delta.  (integer)
suprates
        Returns or sets the 11g override for the supported rateset
        With no args, returns the rateset. Args are a list of rates,
        or 0 or -1 to specify an empty rateset to clear the override.
        List of rates are in Mbps, example: 1 2 5.5 11
scan_channel_time
        Get/Set scan channel time
scan_unassoc_time
        Get/Set unassociated scan channel dwell time
scan_home_time
        Get/Set scan home channel dwell time
scan_passive_time
        Get/Set passive scan channel dwell time
scan_nprobes
        Get/Set scan parameter for number of probes to use per channel scanned
prb_resp_timeout
        Get/Set probe response timeout
channel_qa
        Get last channel quality measurment
channel_qa_start
        Start a channel quality measurment
country Select Country Code for driver operational region
        For simple country setting: wl country <country>
        Where <country> is either a long name or country code from ISO 3166; for example "Germany" or "DE"
        For a specific built-in country definition: wl country <built-in> [<advertised-country>]
        Where <built-in> is a country country code followed by '/' and regulatory revision number.
        For example, "US/3".
        And where <advertised-country> is either a long name or country code from ISO 3166.
        If <advertised-country> is omitted, it will be the same as the built-in country code.
        Use 'wl country list [band(a or b)]' for the list of supported countries
country_ie_override
        To set/get country ie
autocountry_default
        Select Country Code for use with Auto Contry Discovery
join    Join a specified network SSID.
        Usage: join <ssid> [key <0-3>:xxxxx] [imode bss|ibss] [amode open|shared|openshared|wpa|wpapsk|wpa2|wpa2psk|wpanone] [options]
        Options:
        -b MAC, --bssid=MAC    BSSID (xx:xx:xx:xx:xx:xx) to scan and join
        -c CL, --chanspecs=CL  chanspecs (comma or space separated list)
ssid    Set or get a configuration's SSID.
        wl ssid [-C num]|[--cfg=num] [<ssid>]
        If the configuration index 'num' is not given, configuraion #0 is assumed and
        setting will initiate an assoication attempt if in infrastructure mode,
        or join/creation of an IBSS if in IBSS mode,
        or creation of a BSS if in AP mode.
mac    Set or get the list of source MAC address matches.
        wl mac xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]
        To Clear the list: wl mac none
macmode Set the mode of the MAC list.
        0 - Disable MAC address matching.
        1 - Deny association to stations on the MAC list.
        2 - Allow association to stations on the MAC list.
wds    Set or get the list of WDS member MAC addresses.
        Set using a space separated list of MAC addresses.
        wl wds xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]
lazywds Set or get "lazy" WDS mode (dynamically grant WDS membership to anyone).
noise  Get noise (moving average) right after tx in dBm
fqacurcy
        Manufacturing test: set frequency accuracy mode.
        freqacuracy syntax is: fqacurcy <channel>
        Arg is channel number 1-14, or 0 to stop the test.
crsuprs Manufacturing test: set carrier suppression mode.
        carriersuprs syntax is: crsuprs <channel>
        Arg is channel number 1-14, or 0 to stop the test.
longtrain
        Manufacturing test: set longtraining mode.
        longtrain syntax is: longtrain <channel>
        Arg is A band channel number or 0 to stop the test.
band    Returns or sets the current band
        auto - auto switch between available bands (default)
        a - force use of 802.11a band
        b - force use of 802.11b band
bands  Return the list of available 802.11 bands
phylist Return the list of available phytypes
shortslot
        Get current 11g Short Slot Timing mode. (0=long, 1=short)
shortslot_override
        Get/Set 11g Short Slot Timing mode override. (-1=auto, 0=long, 1=short)
shortslot_restrict
        Get/Set AP Restriction on associations for 11g Short Slot Timing capable STAs.
        0 - Do not restrict association based on ShortSlot capability
        1 - Restrict association to STAs with ShortSlot capability
ignore_bcns
        AP only (G mode): Check for beacons without NONERP element(0=Examine beacons, 1=Ignore beacons)
pktcnt  Get the summary of good and bad packets.
upgrade Upgrade the firmware on an embedded device
gmode  Set the 54g Mode (LegacyB|Auto||GOnly|BDeferred|Performance|LRS)
gmode_protection
        Get G protection mode. (0=disabled, 1=enabled)
gmode_protection_control
        Get/Set 11g protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)
gmode_protection_override
        Get/Set 11g protection mode override. (-1=auto, 0=disable, 1=enable)
protection_control
        Get/Set protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)
legacy_erp
        Get/Set 11g legacy ERP inclusion (0=disable, 1=enable)
scb_timeout
        AP only: inactivity timeout value for authenticated stas
assoclist
        AP only: Get the list of associated MAC addresses.
isup    Get driver operational state (0=down, 1=up)
rssi    Get the current RSSI val, for an AP you must specify the mac addr of the STA
rssi_event
        Set parameters associated with RSSI event notification
        usage: wl rssi_event <rate_limit> <rssi_levels>
        rate_limit: Number of events posted to application will be limited to 1 per this rate limit. Set to 0 to disable rate limit.
        rssi_levels: Variable number of RSSI levels (maximum 8)  in increasing order (e.g. -85 -70 -60). An event will be posted each time the RSSI of received beacons/packets cross
fasttimer
        Deprecated. Use fast_timer.
slowtimer
        Deprecated. Use slow_timer.
glacialtimer
        Deprecated. Use glacial_timer.
radar  Enable/Disable radar
radarargs
        Get/Set Radar parameters in
        order as version, npulses, ncontig, min_pw, max_pw, thresh0,
        thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,
        min_fm_lp, max_span_lp, min_deltat, max_deltat,
        autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,
        npulses_stg2, npulses_stg3, percal_mask, quant,
        min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask
radarargs40
        Get/Set Radar parameters for 40Mhz channel in
        order as version, npulses, ncontig, min_pw, max_pw, thresh0,
        thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,
        min_fm_lp, max_span_lp, min_deltat, max_deltat,
        autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,
        npulses_stg2, npulses_stg3, percal_mask, quant,
        min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask
radarthrs
        Set Radar threshold for both 20 & 40MHz BW:
        order as thresh0_20_lo, thresh1_20_lo, thresh0_40_lo, thresh1_40_lo
        thresh0_20_hi, thresh1_20_hi, thresh0_40_hi, thresh1_40_hi
dfs_status
        Get dfs status
interference
        Get/Set interference mitigation mode. Choices are:
        0 = none
        1 = non wlan
        2 = wlan manual
        3 = wlan automatic
        4 = wlan automatic with noise reduction
interference_override
        Get/Set interference mitigation override. Choices are:
        0 = no interference mitigation
        1 = non wlan
        2 = wlan manual
        3 = wlan automatic
        4 = wlan automatic with noise reduction
        -1 = remove override, override disabled
frameburst
        Disable/Enable frameburst mode
pwr_percent
        Get/Set power output percentage
toe    Enable/Disable tcpip offload feature
toe_ol  Get/Set tcpip offload components
toe_stats
        Display checksum offload statistics
toe_stats_clear
        Clear checksum offload statistics
arpoe  Enable/Disable arp agent offload feature
arp_ol  Get/Set arp offload components
arp_peerage
        Get/Set age of the arp entry in minutes
arp_table_clear
        Clear arp cache
arp_hostip
        Add a host-ip address or display them
arp_hostip_clear
        Clear all host-ip addresses
arp_stats
        Display ARP offload statistics
arp_stats_clear
        Clear ARP offload statistics
wet    Get/Set wireless ethernet bridging mode
bi      Get/Set the beacon period (bi=beacon interval)
dtim    Get/Set DTIM
wds_remote_mac
        Get WDS link remote endpoint's MAC address
wds_wpa_role_old
        Get WDS link local endpoint's WPA role (old)
wds_wpa_role
        Get/Set WDS link local endpoint's WPA role
authe_sta_list
        Get authenticated sta mac address list
autho_sta_list
        Get authorized sta mac address list
measure_req
        Send an 802.11h measurement request.
        Usage: wl measure_req <type> <target MAC addr>
        Measurement types are: TPC, Basic, CCA, RPI
        Target MAC addr format is xx:xx:xx:xx:xx:xx
quiet  Send an 802.11h quiet command.
        Usage: wl quiet <TBTTs until start>, <duration (in TUs)>, <offset (in TUs)>
csa    Send an 802.11h channel switch anouncement with chanspec:
        <mode> <count> <channel>[a,b][n][u,l]
        mode (0 or 1)
        count (0-254)
        channel number (0-224)
        band a=5G, b=2G
        bandwidth n=10, non for 20 & 40
        ctl sideband, l=lower, u=upper, default no ctl sideband
constraint
        Send an 802.11h Power Constraint IE
        Usage: wl constraint 1-255 db
rm_req  Request a radio measurement of type basic, cca, or rpi
        specify a series of measurement types each followed by options.
        example: wl rm_req cca -c 1 -d 50 cca -c 6 cca -c 11
        Options:
        -t n  numeric token id for measurement set or measurement
        -c n  channel
        -d n  duration in TUs (1024 us)
        -p    parallel flag, measurement starts at the same time as previous
        Each measurement specified uses the same channel and duration as the
        previous unless a new channel or duration is specified.
rm_rep  Get current radio measurement report
join_pref
        Set/Get join target preferences.
assoc_pref
        Set/Get association preference.
Usage: wl assoc_pref [auto|a|b|g]
wme    Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on, -1=auto)
wme_ac  wl wme_ac ap|sta [be|bk|vi|vo [ecwmax|ecwmin|txop|aifsn|acm <value>] ...]
wme_apsd
        Set APSD (Automatic Power Save Delivery) mode on AP (0=off, 1=on)
wme_apsd_sta
        Set APSD parameters on STA. Driver must be down.
Usage: wl wme_apsd_sta <max_sp_len> <be> <bk> <vi> <vo>
  <max_sp_len>: number of frames per USP: 0 (all), 2, 4, or 6
  <xx>: value 0 to disable, 1 to enable U-APSD per AC
wme_dp  Set AC queue discard policy.
Usage: wl wme_dp <be> <bk> <vi> <vo>
  <xx>: value 0 for newest-first, 1 for oldest-first
wme_counters
        print WMM stats
wme_clear_counters
        clear WMM counters
wme_tx_params
        wl wme_tx_params [be|bk|vi|vo [short|sfb|long|lfb|max_rate <value>] ...]
wme_maxbw_params
        wl wme_maxbw_params [be|bk|vi|vo <value> ....]
lifetime
        Set Lifetime parameter (milliseconds) for each ac. wl lifetime be|bk|vi|vo [<value>]
</pre>




[[Category:Wireless]]
[[Category:Wireless]]

Revision as of 10:04, 3 September 2016

Links

Firmware download:

Datasheet: http://internethelp.centurylink.com/internethelp/pdf/modems/datasheet-c2100t.pdf

Info about FCC testing: https://fccid.io/RSE-C2100T#exhibits

DSLReports forums: https://www.dslreports.com/forum/centurylink

Telnet

Telnet access:

  • Log in
  • Advanced setup
  • Remote console
  • Enable telnet from WAN or LAN

When logging in via telnet, I see this: BCM963268 Broadband Router

Telnet Commands

Logging in and typing a question mark for help shows all the available commands: 

 > ?
?
help
logout
exit
quit
reboot
env_list
autodetect
adsl
xdslctl0
xdslctl1
loglevel
meminfo
dnsproxy
ping
voice
dect
wlctl
lanhosts
passwd
restoredefault
save
swversion
uptime
cfgupdate
swupdate
exitOnIdle
wan
igmp
imageServer
pm
led
wpsbtn
snoop_on
snoop_off

These commands provide lots of information about the router. Here's a brief rundown:

  • env_list - lists all environmental variables, including _PROD_SERIAL_NBR, _BOOTLOADER_VERSION, _WL0_WEPKEY_SERIAL, _WL0_WPAKEY_SERIAL, _WL0_PIN_SERIAL
  • autodetect - sets parameters (start_delay, cycle_delay, ppp_attempts, dhcp_attempts) for router
  • adsl - asymmetric digital subscriber line, faster data rates over copper phone lines than by using conventional VOIP modem
  • xdslctl0 - not sure, but looks like another advanced command line interface, related to ADSL
  • xdslctl1 - ditto
  • meminfo - info about how much memory is being used
  • dnsproxy - dumps info or stats (in my case, nothing printed out........)
  • ping - works like normal ping, say ping IPADDR
  • voice - this is basically the program that you use to interface with VOIP settings on the router. See below for detailed output.
  • dect - dect is some kind of phone handset base station functionality. more of this SIP/phone/dialing stuff.
  • wlctl - wireless LAN control program
  • lanhosts
  • passwd - duh, changes password
  • restoredefault - duh, restores default factory settings
  • save
  • swversion


Voice

Here's the output for the voice command: 

 > voice
Command syntax:
voice --help                      -  show the voice command syntax
voice show                        -  show the voice parameters
voice show stats                  -  show call statistics
voice start                       -  start the voice application
voice stop                        -  stop the voice application
voice save                        -  store voice params to flash
voice reboot                      -  restart the voice application
voice set <param> <arg1> <arg2>.. -  set a provisionable parameter
List of voice set params and args:
defaults        <None>                      - Default VoIP setup
boundIfname     <LAN|Any_WAN|(WAN IfName, e.g. nas_0_0_35)> - vodsl network interface
ipAddrFamily    <IPv4|IPv6>                 - IP address family
pstnDialPlan    <pstn line#> <dialPlan>     - PSTN dial plan
pstnRouteRule   <pstn line#> <Auto|Voip|Line> - PSTN Route rule
pstnRouteData   <pstn line#> <line #|URL for VOIP> - PSTN Route data
locale          <srvPrv#> <region>          - 2 or 3 character code
DTMFMethod      <srvPrv#> <InBand|RFC2833|SIPInfo> - DTMF digit passing method
hookFlashMethod <srvPrv#> <SIPInfo|None>    - Hook flash method
transport       <srvPrv#> <UDP|TCP|TLS>     - transport protocol
srtpOption      <srvPrv#> <Mandatory|Optional|Disabled> - SRTP usage option
regRetryInt     <srvPrv#> <seconds>         - SIP register retryinterval
regExpires      <srvPrv#> <seconds>         - Register expires hdr val
rtpDSCPMark     <srvPrv#> <mark>            - RTP outgoing DSCP mark
logServer       <srvPrv#> <hostName|IP>     - Log server
logPort         <srvPrv#> <port>            - Log server port
digitMap        <srvPrv#> <digitmap>        - dial digit map
T38             <srvPrv#> on|off            - enable/disable T38
V18             <srvPrv#> on|off            - enable/disable V.18 detection
reg             <srvPrv#> <hostName|IP>     - SIP registrar server
regPort         <srvPrv#> <port>            - SIP registrar server port
proxy           <srvPrv#> <hostName|IP>     - SIP proxy server
proxyPort       <srvPrv#> <port>            - SIP proxy server port
obProx          <srvPrv#> <hostName|IP>     - SIP outbound proxy
obProxPort      <srvPrv#> <port>            - SIP outbound proxy port
sipDomain       <srvPrv#> <CPE_domainName>  - SIP user agent domain
sipPort         <srvPrv#> <port>            - SIP user agent port
sipDSCPMark     <srvPrv#> <mark>            - SIP outgoing DSCP mark
musicServer     <srvPrv#> <hostName|IP>     - SIP music server
musicSrvPort    <srvPrv#> <port>            - SIP music server port
tagMatching     <srvPrv#> <on|off>          - SIP to tag matching
timerB          <srvPrv#> <time in ms>      - SIP protocol B timer
timerF          <srvPrv#> <time in ms>      - SIP protocol F timer
lineStatus      <srvPrv#> <accnt#> <on|off> - Activate line
physEndpt       <srvPrv#> <accnt#> <id>     - Phys Endpt
extension       <srvPrv#> <accnt#> <URI>    - SIP extension
dispName        <srvPrv#> <accnt#> <Name>   - SIP Display Name
authName        <srvPrv#> <accnt#> <name>   - SIP auth name
authPwd         <srvPrv#> <accnt#> <pwd>    - SIP auth password
MWIEnable       <srvPrv#> <accnt#> <on|off> - Msg Waiting Indication
cfwdNum         <srvPrv#> <accnt#> <number> - call forward number
cfwdAll         <srvPrv#> <accnt#> <on|off> - call forward all
cfwdNoAns       <srvPrv#> <accnt#> <on|off> - call forward no answer
cfwdBusy        <srvPrv#> <accnt#> <on|off> - call forward busy
callWait        <srvPrv#> <accnt#> <on|off> - call waiting
anonBlck        <srvPrv#> <accnt#> <on|off> - Anonymous call rcv blcking
anonCall        <srvPrv#> <accnt#> <on|off> - Anonymous outgng calls
DND             <srvPrv#> <accnt#> <on|off> - do not disturb
CCBS            <srvPrv#> <accnt#> <on|off> - Call completion on busy
speedDial       <srvPrv#> <accnt#> <on|off> - Speed dial
warmLine        <srvPrv#> <accnt#> <on|off> - Warm line
warmLineNum     <srvPrv#> <accnt#> <number> - Warm line number
callBarring     <srvPrv#> <accnt#> <on|off> - Call barring
callBarrPin     <srvPrv#> <accnt#> <number> - Call barring pin
callBarrDigMap  <srvPrv#> <accnt#> <digitmap> - Call barring digit map
netPrivacy      <srvPrv#> <accnt#> <on|off> - Network privacy
vmwi            <srvPrv#> <accnt#> <on|off> - Visual message waiting indication
vad             <srvPrv#> <accnt#> <on|off> - enable vad
pTime           <srvPrv#> <accnt#> <pTime>  - packetization period
codecList       <srvPrv#> <accnt#> <codec(1)[,codec(2)]> - codec priority list
rxGain          <srvPrv#> <accnt#> <rxGain> - rxGain (dB)
txGain          <srvPrv#> <accnt#> <txGain> - txGain (dB)

Now trying voice show to show values of parameters: 

 > voice show


Global Parameters:
------------------
BoundIfName          : Any_WAN
IP address family    : IPv4
Vodsl logLevel       : Error
Management Protocol  : TR69

Service Provider 0:
--------------------
   Associated Voice Profile: 1
   Locale                  : USA
   DTMFMethod              : RFC2833
   HookFlashMethod         : None
   DigitMap                : #xx|[2-9]11|1[2-9]11|[2-9]xxxxxxxxx|1[2-9]xxxxxxxxx|x.T
   Log Server Addr         :
   Log Server Port         : 0
   T38                     : on
   V18                     : off
   RTPDSCPMark             : 46
   SIP:
      Domain               :
      Port                 : 0
      Transport            : UDP
      RegExpires           : 0
      RegRetryInterval     : 0
      DSCPMark             : 40
      Registrar Addr       :
      Registrar Port       : 0
      Proxy Addr           :
      Proxy Port           : 0
      OutBoundProxy Addr   :
      OutBoundProxy Port   : 0
      Music Server Addr    :
      Music Server Port    : 0
      To Tag Matching      : On
      Timer B ( in ms )    : 32000
      Timer F ( in ms )    : 32000
      SRTP Usage Option    : Optional

   Account 0:
   -----------
      ActivationStatus        : Disabled
      VoipServiceStatus       : Disabled
      CallStatus              : Idle
      Associated CM Acnt      : 0
      PhysEndpt               : 1
      Extension               :
      DisplayName             :
      AuthName                :
      AuthPwd                 :
      TxGain                  : 0 dB
      RxGain                  : 0 dB
      CALLFEATURES:
         MWI                  : off
         CallWaiting          : on
         CFWDNum              :
         CallFwdAll           : off
         CallFwdBusy          : off
         CallFwdNoans         : off
         AnonymousOutgoingCall: off
         AnonymousCallRcvBlock: off
         DoNotDisturb         : off
         CallCompOnBusy       : off
         SpeedDial            : off
         WarmLine             : off
         WarmLineNum          :
         CallBarring          : off
         CallBarringMode      : None
         CallBarringPin       : 9999
         CallBarringDigitMap  :
         NetPrivacy           : off
         VMWI                 : off
      CODECSETTINGS:
         VAD                  : off
         pTime                : 20
         CodecList            : (0) G.722
                                (1) G.711MuLaw
                                (2) T38
                                (3) NTE

   Account 1:
   -----------
      ActivationStatus        : Disabled
      VoipServiceStatus       : Disabled
      CallStatus              : Idle
      Associated CM Acnt      : 1
      PhysEndpt               : 1
      Extension               :
      DisplayName             :
      AuthName                :
      AuthPwd                 :
      TxGain                  : 0 dB
      RxGain                  : 0 dB
      CALLFEATURES:
         MWI                  : off
         CallWaiting          : on
         CFWDNum              :
         CallFwdAll           : off
         CallFwdBusy          : off
         CallFwdNoans         : off
         AnonymousOutgoingCall: off
         AnonymousCallRcvBlock: off
         DoNotDisturb         : off
         CallCompOnBusy       : off
         SpeedDial            : off
         WarmLine             : off
         WarmLineNum          :
         CallBarring          : off
         CallBarringMode      : None
         CallBarringPin       : 9999
         CallBarringDigitMap  :
         NetPrivacy           : off
         VMWI                 : off
      CODECSETTINGS:
         VAD                  : off
         pTime                : 20
         CodecList            : (0) G.722
                                (1) G.711MuLaw
                                (2) T38
                                (3) NTE

wlctl

 > wlctl
Usage: wlctl [-a|i <adapter>] [-h] [-d|u|x] <command> [arguments]

  -h        this message and command descriptions
  -h [cmd]  command description for cmd
  -a, -i    adapter name or number
  -d        output format signed integer
  -u        output format unsigned integer
  -x        output format hexdecimal

ver     get version information

cmds    generate a short list of available commands

up      reinitialize and mark adapter up (operational)

down    reset and mark adapter down (disabled)

out     mark adapter down but do not reset hardware(disabled)
        On dualband cards, cards must be bandlocked before use.

clk     set board clock state. return error for set_clk attempt if the driver is not down
        0: clock off
        1: clock on

restart Restart driver.  Driver must already be down.

reboot  Reboot platform

radio   Set the radio on or off.
        "on" or "off"

dump    Give suboption "list" to list various suboptions

srclear Clears first 'len' bytes of the srom, len in decimal or hex
        Usage: srclear <len>

srdump  print contents of SPROM to stdout

srwrite Write the srom: srwrite byteoffset value

srcrc   Get the CRC for input binary file

ciswrite
        Write specified <file> to the SDIO CIS source (either SROM or OTP)

cisupdate
        Write a hex byte stream to specified byte offset to the CIS source (either SROM or OTP)
--preview option allows you to review the update without committing it
        <byte offset> <hex byte stream> [--preview]

cisdump Display the content of the SDIO CIS source
        -b <file> -- also write raw bytes to <file>
        <len> -- optional count of bytes to display (must be even)

cis_source
        Display which source is used for the SDIO CIS

cisconvert
        Print CIS tuple for given name=value pair

rdvar   Read a named variable to the srom

wrvar   Write a named variable to the srom

nvram_source
        Display which source is used for nvram

nvram_dump
        print nvram variables to stdout

nvset   set an nvram variable
        name=value (no spaces around '=')

nvget   get the value of an nvram variable

nvram_get
        get the value of an nvram variable

revinfo get hardware revision information

customvar1
        print the value of customvar1 in hex format

msglevel
        set driver console debugging message bitvector
        type 'wl msglevel ?' for values

phymsglevel
        set phy debugging message bitvector
        type 'wl phymsglevel ?' for values

PM      set driver power management mode:
        0: CAM (constantly awake)
        1: PS  (power-save)
        2: FAST PS mode

wake    set driver power-save mode sleep state:
        0: core-managed
        1: awake

promisc set promiscuous mode ethernet address reception
        0 - disable
        1 - enable

monitor set monitor mode
        0 - disable
        1 - enable active monitor mode (interface still operates)

frag    Deprecated. Use fragthresh.

rts     Deprecated. Use rtsthresh.

cwmin   Set the cwmin.  (integer [1, 255])

cwmax   Set the cwmax.  (integer [256, 2047])

srl     Set the short retry limit.  (integer [1, 255])

lrl     Set the long retry limit.  (integer [1, 255])

rate    force a fixed rate:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

mrate   force a fixed multicast rate:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

a_rate  force a fixed rate for the A PHY:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

a_mrate force a fixed multicast rate for the A PHY:
        valid values for 802.11a are (6, 9, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

bg_rate force a fixed rate for the B/G PHY:
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

bg_mrate
        force a fixed multicast rate for the B/G PHY:
        valid values for 802.11b are (1, 2, 5.5, 11)
        valid values for 802.11g are (1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54)
        -1 (default) means automatically determine the best rate

infra   Set Infrastructure mode: 0 (IBSS) or 1 (Infra BSS)

ap      Set AP mode: 0 (STA) or 1 (AP)

bssid   Get the BSSID value, error if STA and not associated

bssmax  get number of BSSes

channel Set the channel:
        valid channels for 802.11b/g (2.4GHz band) are 1 through 14
        valid channels for 802.11a  (5 GHz band) are:
                36, 40, 44, 48, 52, 56, 60, 64,
                100, 104, 108, 112, 116,120, 124, 128, 132, 136, 140,
                149, 153, 157, 161,
                184, 188, 192, 196, 200, 204, 208, 212, 216

cur_mcsset
        Get the current mcs set

chanspecs
        Get all the valid chanspecs (default: all within current locale):
        -b band (5(a) or 2(b/g))
        -w bandwidth, 10,20 or 40
        [-c country_abbrev]

chanspec
        Set <channel>[a,b][n][u,l]
        channel number (0-224)
        band a=5G, b=2G, default to 2G if channel <= 14
        bandwidth, n=10, none for 20 & 40
        ctl sideband, l=lower, u=upper
OR Set channel with legacy format:
        -c channel number (0-224)
        -b band (5(a) or 2(b/g))
        -w bandwidth, 10,20 or 40
        -s ctl sideband, -1=lower, 0=none, 1=upper

dfs_channel_forced
        Set <channel>[a,b][n][u,l]
        channel number (0-224)
        band a=5G, b=2G, default to 2G if channel <= 14
        bandwidth, n=10, non for 20 & 40
        ctl sideband, l=lower, u=upper

tssi    Get the tssi value from radio

txpwr   Set tx power in milliwatts.  Range [1, 84].

txpwr1  Set tx power in in various units. Choose one of (default: dbm):
        -d dbm units
        -q quarter dbm units
        -m milliwatt units
Can be combined with:
        -o turn on override to disable regulatory and other limitations
Use wl txpwr -1 to restore defaults

txpathpwr
        Turn the tx path power on or off on 2050 radios

txpwrlimit
        Return current tx power limit

powerindex
        Set the transmit power for A band(0-63).
        -1 - default value

atten   Set the transmit attenuation for B band. Args: bb radio txctl1.
        auto to revert to automatic control
        manual to supspend automatic control

phyreg  Get/Set a phy register:
        offset [ value ] [ band ]

radioreg
        Get/Set a radio register:
        offset [ value ] [ band/core ]
HTPHY:
        Get a radio register: wl radioreg [ offset ] [ cr0/cr1/cr2 ]
        Set a radio register: wl radioreg [ offset ] [ value ] [ cr0/cr1/cr2/all ]


ucflags Get/Set ucode flags 1, 2, 3(16 bits each)
        offset [ value ] [ band ]

shmem   Get/Set a shared memory location:
        offset [ value ] [band ]

macreg  Get/Set any mac registers(include IHR and SB):
        macreg offset size[2,4] [ value ] [ band ]

ucantdiv
        Enable/disable ucode antenna diversity (1/0 or on/off)

gpioout Set any GPIO pins to any value. Use with caution as GPIOs would be assigned to chipcommon
        Usage: gpiomask gpioval

devpath print device path

jtagureg
        g/set JTAG user registers

coma    Put the router in a catatonic state

pllreset
        set the pll to reset value
        Usage: wl pllreset

pcieserdesreg
        g/set SERDES registers: dev offset [val]

ampdu_activate_test
        actiate

ampdu_tid
        enable/disable per-tid ampdu; usage: wl ampdu_tid <tid> [0/1]

ampdu_retry_limit_tid
        Set per-tid ampdu retry limit; usage: wl ampdu_retry_limit_tid <tid> [0~31]

ampdu_rr_retry_limit_tid
        Set per-tid ampdu regular rate retry limit; usage: wl ampdu_rr_retry_limit_tid <tid> [0~31]

ampdu_send_addba
        send addba to specified ea-tid; usage: wl ampdu_send_addba <tid> <ea>

ampdu_send_delba
        send delba to specified ea-tid; usage: wl ampdu_send_delba <tid> <ea>

ampdu_clear_dump
        clear ampdu counters

dpt_deny
        adds/removes ea to dpt deny list
        usage: wl dpt_deny <add,remove> <ea>

dpt_endpoint
        creates/updates/deletes dpt endpoint for ea
        usage: wl dpt_endpoint <create, update, delete> <ea>

dpt_pmk sets DPT pre-shared key

dpt_fname
        sets/gets DPT friendly name

dpt_list
        gets status of all dpt peers

actframe
        Send a Vendor specific Action frame to a channel
        usage: wl actframe <Dest Mac Addr> <data> channel dwell-time <BSSID>

antdiv  Set antenna diversity for rx
        0 - force use of antenna 0
        1 - force use of antenna 1
        3 - automatic selection of antenna diversity

txant   Set the transmit antenna
        0 - force use of antenna 0
        1 - force use of antenna 1
        3 - use the RX antenna selection that was in force during
            the most recently received good PLCP header

plcphdr Set the plcp header.
        "long" or "auto" or "debug"

phytype Get phy type

rateparam
        set driver rate selection tunables
        arg 1: tunable id
        arg 2: tunable value

wepstatus
        Set or Get WEP status
        wepstatus [on|off]

primary_key
        Set or get index of primary key

addwep  Set an encryption key.  The key must be 5, 13 or 16 bytes long, or
        10, 26, 32, or 64 hex digits long.  The encryption algorithm is
        automatically selected based on the key size. keytype is accepted
        only when key length is 16 bytes/32 hex digits and specifies
        whether AES-OCB or AES-CCM encryption is used. Default is ccm.
        WAPI is selected if key len is 32 and arguments contain wapi.
        addwep <keyindex> <keydata> [ocb | ccm | wapi] [notx] [xx:xx:xx:xx:xx:xx]

rmwep   Remove the encryption key at the specified key index.

keys    Prints a list of the current WEP keys

tsc     Print Tx Sequence Couter for key at specified key index.

wsec_test
        Generate wsec errors
        wsec_test <test_type> <keyindex|xx:xx:xx:xx:xx:xx>
        type 'wl wsec_test ?' for test_types

tkip_countermeasures
        Enable or disable TKIP countermeasures (TKIP-enabled AP only)
        0 - disable
        1 - enable

wsec_restrict
        Drop unencrypted packets if WSEC is enabled
        0 - disable
        1 - enable

eap     restrict traffic to 802.1X packets until 802.1X authorization succeeds
        0 - disable
        1 - enable

cur_etheraddr
        Get/set the current hw address

perm_etheraddr
        Get the permanent address from NVRAM

authorize
        restrict traffic to 802.1X packets until 802.1X authorization succeeds

deauthorize
        do not restrict traffic to 802.1X packets until 802.1X authorization succeeds

deauthenticate
        deauthenticate a STA from the AP with optional reason code (AP ONLY)

wsec    wireless security bit vector
        1 - WEP enabled
        2 - TKIP enabled
        4 - AES enabled
        8 - WSEC in software
        0x80 - FIPS enabled
        0x100 - WAPI enabled

auth    set/get 802.11 authentication type. 0 = OpenSystem, 1= SharedKey, 2=Open/Shared

wpa_auth
        Bitvector of WPA authorization modes:
        1       WPA-NONE
        2       WPA-802.1X/WPA-Professional
        4       WPA-PSK/WPA-Personal
        64      WPA2-802.1X/WPA2-Professional
        128     WPA2-PSK/WPA2-Personal
        0       disable WPA

wpa_cap set/get 802.11i RSN capabilities

set_pmk Set passphrase for PMK in driver-resident supplicant.

scan    Initiate a scan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST   [active|passive|prohibit] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

iscan_s Initiate an incremental scan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST   [active|passive|prohibit] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

iscan_c Continue an incremental scan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST   [active|passive|prohibit] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

scancache_clear
        clear the scan cache

escan   Start an escan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST   [active|passive|prohibit] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

escanabort
        Abort an escan.
        Default to an active scan across all channels for any SSID.
        Optional arg: SSIDs, list of [up to 10] SSIDs to scan (comma or space separated).
        Options:
        -s S, --ssid=S          SSIDs to scan
        -t ST, --scan_type=ST   [active|passive|prohibit] scan type
        --bss_type=BT           [bss/infra|ibss/adhoc] bss type to scan
        -b MAC, --bssid=MAC     particular BSSID MAC address to scan, xx:xx:xx:xx:xx:xx
        -n N, --nprobes=N       number of probes per scanned channel
        -a N, --active=N        dwell time per channel for active scanning
        -p N, --passive=N       dwell time per channel for passive scanning
        -h N, --home=N          dwell time for the home channel between channel scans
        -c L, --channels=L      comma or space separated list of channels to scan

passive Puts scan engine into passive mode

regulatory
        Get/Set regulatory domain mode (802.11d). Driver must be down.

spect   Get/Set 802.11h Spectrum Management mode.
        0 - Off
        1 - Loose interpretation of 11h spec - may join non-11h APs
        2 - Strict interpretation of 11h spec - may not join non-11h APs
        3 - Disable 11h and enable 11d
        4 - Loose interpretation of 11h+d spec - may join non-11h APs

scanabort
        Abort a scan.

scanresults
        Return results from last scan.

iscanresults
        Return results from last iscan. Specify a buflen (max 8188)
        to artificially limit the size of the results buffer.
        iscanresults [buflen]

assoc   Print information about current network association.
        (also known as "status")

status  Print information about current network association.
        (also known as "assoc")

disassoc
        Disassociate from the current BSS/IBSS.

channels
        Return valid channels for the current settings.

channels_in_country
        Return valid channels for the country specified.
        Arg 1 is the country abbreviation
        Arg 2 is the band(a or b)

curpower
        Return current tx power settings.
        -q (quiet): estimated power only.

curppr  Return current tx power per rate offset.


txinstpwr
        Return tx power based on instant TSSI

scansuppress
        Suppress all scans for testing.
        0 - allow scans
        1 - suppress scans

evm     Start an EVM test on the given channel, or stop EVM test.
        Arg 1 is channel number 1-14, or "off" or 0 to stop the test.
        Arg 2 is optional rate (1, 2, 5.5 or 11)

rateset Returns or sets the supported and basic rateset, (b) indicates basic
        With no args, returns the rateset. Args are
        rateset "default" | "all" | <arbitrary rateset> -m <arbitrary mcsset>
                default - driver defaults
                all - all rates are basic rates
                arbitrary rateset - list of rates
                arbitrary mcsset - list of mcs rates octets, each bit representing
                                corresponding mcs
        List of rates are in Mbps and each rate is optionally followed
        by "(b)" or "b" for a Basic rate. Example: 1(b) 2b 5.5 11
        At least one rate must be Basic for a legal rateset.

roam_trigger
        Get or Set the roam trigger RSSI threshold:
        Get: roam_trigger [a|b]
        Set: roam_trigger <integer> [a|b|all]
        integer -   0: default
                    1: optimize bandwidth
                    2: optimize distance
            [-1, -99]: dBm trigger value

roam_delta
        Set the roam candidate qualification delta. roam_delta [integer [, a/b]]

roam_scan_period
        Set the roam candidate qualification delta.  (integer)

suprates
        Returns or sets the 11g override for the supported rateset
        With no args, returns the rateset. Args are a list of rates,
        or 0 or -1 to specify an empty rateset to clear the override.
        List of rates are in Mbps, example: 1 2 5.5 11

scan_channel_time
        Get/Set scan channel time

scan_unassoc_time
        Get/Set unassociated scan channel dwell time

scan_home_time
        Get/Set scan home channel dwell time

scan_passive_time
        Get/Set passive scan channel dwell time

scan_nprobes
        Get/Set scan parameter for number of probes to use per channel scanned

prb_resp_timeout
        Get/Set probe response timeout

channel_qa
        Get last channel quality measurment

channel_qa_start
        Start a channel quality measurment

country Select Country Code for driver operational region
        For simple country setting: wl country <country>
        Where <country> is either a long name or country code from ISO 3166; for example "Germany" or "DE"

        For a specific built-in country definition: wl country <built-in> [<advertised-country>]
        Where <built-in> is a country country code followed by '/' and regulatory revision number.
        For example, "US/3".
        And where <advertised-country> is either a long name or country code from ISO 3166.
        If <advertised-country> is omitted, it will be the same as the built-in country code.

        Use 'wl country list [band(a or b)]' for the list of supported countries

country_ie_override
        To set/get country ie

autocountry_default
        Select Country Code for use with Auto Contry Discovery

join    Join a specified network SSID.
        Usage: join <ssid> [key <0-3>:xxxxx] [imode bss|ibss] [amode open|shared|openshared|wpa|wpapsk|wpa2|wpa2psk|wpanone] [options]
        Options:
        -b MAC, --bssid=MAC     BSSID (xx:xx:xx:xx:xx:xx) to scan and join
        -c CL, --chanspecs=CL   chanspecs (comma or space separated list)

ssid    Set or get a configuration's SSID.
        wl ssid [-C num]|[--cfg=num] [<ssid>]
        If the configuration index 'num' is not given, configuraion #0 is assumed and
        setting will initiate an assoication attempt if in infrastructure mode,
        or join/creation of an IBSS if in IBSS mode,
        or creation of a BSS if in AP mode.

mac     Set or get the list of source MAC address matches.
        wl mac xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]
        To Clear the list: wl mac none

macmode Set the mode of the MAC list.
        0 - Disable MAC address matching.
        1 - Deny association to stations on the MAC list.
        2 - Allow association to stations on the MAC list.

wds     Set or get the list of WDS member MAC addresses.
        Set using a space separated list of MAC addresses.
        wl wds xx:xx:xx:xx:xx:xx [xx:xx:xx:xx:xx:xx ...]

lazywds Set or get "lazy" WDS mode (dynamically grant WDS membership to anyone).

noise   Get noise (moving average) right after tx in dBm

fqacurcy
        Manufacturing test: set frequency accuracy mode.
        freqacuracy syntax is: fqacurcy <channel>
        Arg is channel number 1-14, or 0 to stop the test.

crsuprs Manufacturing test: set carrier suppression mode.
        carriersuprs syntax is: crsuprs <channel>
        Arg is channel number 1-14, or 0 to stop the test.

longtrain
        Manufacturing test: set longtraining mode.
        longtrain syntax is: longtrain <channel>
        Arg is A band channel number or 0 to stop the test.

band    Returns or sets the current band
        auto - auto switch between available bands (default)
        a - force use of 802.11a band
        b - force use of 802.11b band

bands   Return the list of available 802.11 bands

phylist Return the list of available phytypes

shortslot
        Get current 11g Short Slot Timing mode. (0=long, 1=short)

shortslot_override
        Get/Set 11g Short Slot Timing mode override. (-1=auto, 0=long, 1=short)

shortslot_restrict
        Get/Set AP Restriction on associations for 11g Short Slot Timing capable STAs.
        0 - Do not restrict association based on ShortSlot capability
        1 - Restrict association to STAs with ShortSlot capability

ignore_bcns
        AP only (G mode): Check for beacons without NONERP element(0=Examine beacons, 1=Ignore beacons)

pktcnt  Get the summary of good and bad packets.

upgrade Upgrade the firmware on an embedded device

gmode   Set the 54g Mode (LegacyB|Auto||GOnly|BDeferred|Performance|LRS)

gmode_protection
        Get G protection mode. (0=disabled, 1=enabled)

gmode_protection_control
        Get/Set 11g protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)

gmode_protection_override
        Get/Set 11g protection mode override. (-1=auto, 0=disable, 1=enable)

protection_control
        Get/Set protection mode control alg.(0=always off, 1=monitor local association, 2=monitor overlapping BSS)

legacy_erp
        Get/Set 11g legacy ERP inclusion (0=disable, 1=enable)

scb_timeout
        AP only: inactivity timeout value for authenticated stas

assoclist
        AP only: Get the list of associated MAC addresses.

isup    Get driver operational state (0=down, 1=up)

rssi    Get the current RSSI val, for an AP you must specify the mac addr of the STA

rssi_event
        Set parameters associated with RSSI event notification
        usage: wl rssi_event <rate_limit> <rssi_levels>
        rate_limit: Number of events posted to application will be limited to 1 per this rate limit. Set to 0 to disable rate limit.
        rssi_levels: Variable number of RSSI levels (maximum 8)  in increasing order (e.g. -85 -70 -60). An event will be posted each time the RSSI of received beacons/packets cross

fasttimer
        Deprecated. Use fast_timer.

slowtimer
        Deprecated. Use slow_timer.

glacialtimer
        Deprecated. Use glacial_timer.

radar   Enable/Disable radar

radarargs
        Get/Set Radar parameters in
        order as version, npulses, ncontig, min_pw, max_pw, thresh0,
        thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,
        min_fm_lp, max_span_lp, min_deltat, max_deltat,
        autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,
        npulses_stg2, npulses_stg3, percal_mask, quant,
        min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask

radarargs40
        Get/Set Radar parameters for 40Mhz channel in
        order as version, npulses, ncontig, min_pw, max_pw, thresh0,
        thresh1, blank, fmdemodcfg, npulses_lp, min_pw_lp, max_pw_lp,
        min_fm_lp, max_span_lp, min_deltat, max_deltat,
        autocorr, st_level_time, t2_min, fra_pulse_err, npulses_fra,
        npulses_stg2, npulses_stg3, percal_mask, quant,
        min_burst_intv_lp, max_burst_intv_lp, nskip_rst_lp, max_pw_tol, feature_mask

radarthrs
        Set Radar threshold for both 20 & 40MHz BW:
        order as thresh0_20_lo, thresh1_20_lo, thresh0_40_lo, thresh1_40_lo
        thresh0_20_hi, thresh1_20_hi, thresh0_40_hi, thresh1_40_hi

dfs_status
        Get dfs status

interference
        Get/Set interference mitigation mode. Choices are:
        0 = none
        1 = non wlan
        2 = wlan manual
        3 = wlan automatic
        4 = wlan automatic with noise reduction

interference_override
        Get/Set interference mitigation override. Choices are:
        0 = no interference mitigation
        1 = non wlan
        2 = wlan manual
        3 = wlan automatic
        4 = wlan automatic with noise reduction
        -1 = remove override, override disabled

frameburst
        Disable/Enable frameburst mode

pwr_percent
        Get/Set power output percentage

toe     Enable/Disable tcpip offload feature

toe_ol  Get/Set tcpip offload components

toe_stats
        Display checksum offload statistics

toe_stats_clear
        Clear checksum offload statistics

arpoe   Enable/Disable arp agent offload feature

arp_ol  Get/Set arp offload components

arp_peerage
        Get/Set age of the arp entry in minutes

arp_table_clear
        Clear arp cache

arp_hostip
        Add a host-ip address or display them

arp_hostip_clear
        Clear all host-ip addresses

arp_stats
        Display ARP offload statistics

arp_stats_clear
        Clear ARP offload statistics

wet     Get/Set wireless ethernet bridging mode

bi      Get/Set the beacon period (bi=beacon interval)

dtim    Get/Set DTIM

wds_remote_mac
        Get WDS link remote endpoint's MAC address

wds_wpa_role_old
        Get WDS link local endpoint's WPA role (old)

wds_wpa_role
        Get/Set WDS link local endpoint's WPA role

authe_sta_list
        Get authenticated sta mac address list

autho_sta_list
        Get authorized sta mac address list

measure_req
        Send an 802.11h measurement request.
        Usage: wl measure_req <type> <target MAC addr>
        Measurement types are: TPC, Basic, CCA, RPI
        Target MAC addr format is xx:xx:xx:xx:xx:xx

quiet   Send an 802.11h quiet command.
        Usage: wl quiet <TBTTs until start>, <duration (in TUs)>, <offset (in TUs)>

csa     Send an 802.11h channel switch anouncement with chanspec:
        <mode> <count> <channel>[a,b][n][u,l]
        mode (0 or 1)
        count (0-254)
        channel number (0-224)
        band a=5G, b=2G
        bandwidth n=10, non for 20 & 40
        ctl sideband, l=lower, u=upper, default no ctl sideband

constraint
        Send an 802.11h Power Constraint IE
        Usage: wl constraint 1-255 db

rm_req  Request a radio measurement of type basic, cca, or rpi
        specify a series of measurement types each followed by options.
        example: wl rm_req cca -c 1 -d 50 cca -c 6 cca -c 11
        Options:
        -t n  numeric token id for measurement set or measurement
        -c n  channel
        -d n  duration in TUs (1024 us)
        -p    parallel flag, measurement starts at the same time as previous

        Each measurement specified uses the same channel and duration as the
        previous unless a new channel or duration is specified.

rm_rep  Get current radio measurement report

join_pref
        Set/Get join target preferences.

assoc_pref
        Set/Get association preference.
Usage: wl assoc_pref [auto|a|b|g]

wme     Set WME (Wireless Multimedia Extensions) mode (0=off, 1=on, -1=auto)

wme_ac  wl wme_ac ap|sta [be|bk|vi|vo [ecwmax|ecwmin|txop|aifsn|acm <value>] ...]

wme_apsd
        Set APSD (Automatic Power Save Delivery) mode on AP (0=off, 1=on)

wme_apsd_sta
        Set APSD parameters on STA. Driver must be down.
Usage: wl wme_apsd_sta <max_sp_len> <be> <bk> <vi> <vo>
   <max_sp_len>: number of frames per USP: 0 (all), 2, 4, or 6
   <xx>: value 0 to disable, 1 to enable U-APSD per AC

wme_dp  Set AC queue discard policy.
Usage: wl wme_dp <be> <bk> <vi> <vo>
   <xx>: value 0 for newest-first, 1 for oldest-first

wme_counters
        print WMM stats

wme_clear_counters
        clear WMM counters

wme_tx_params
        wl wme_tx_params [be|bk|vi|vo [short|sfb|long|lfb|max_rate <value>] ...]

wme_maxbw_params
        wl wme_maxbw_params [be|bk|vi|vo <value> ....]

lifetime
        Set Lifetime parameter (milliseconds) for each ac. wl lifetime be|bk|vi|vo [<value>]
Retrieved from "https://charlesreid1.com/w/index.php?title=Technicolor_C2100T&oldid=13733"