RaspberryPi/Hotspot

Making a Raspberry Pi a hotspot

See https://www.raspberrypi.org/documentation/configuration/wireless/access-point.md

Installing Stuff

sudo apt install dnsmasq hostapd dhcpcd5

Edit dhcpcd config file

Edit /etc/dhcpcd.conf and modify it to contain this:

interface wlan0
    static ip_address=192.168.4.1/24
    nohook wpa_supplicant

replace wlan0 with whatever interface you want to use.

Restart dhcpcd service

sudo service dhcpcd restart

Edit dnsmmasq config file

Edit the dnsmasq config file /etc/dnsmasq.conf, which determines what range of ip addresses will be handed out and for how long. Modify it to contain this:

interface=wlan1
dhcp-range=192.168.4.2,192.168.4.20,255.255.255.0,24h

This will hand out IPs starting at 192.168.4.2 and ending at 192.168.4.20, lasting for 24 hours lease time.

Modify wlan0 to whatever interface you are using to provide the wifi network.

Restart dnsmasq service

If you are installing dnsmasq fresh, enable then start the service:

sudo systemctl enable dnsmasq
sudo systemctl start dnsmasq

or reload/restart the service:

sudo systemctl reload dnsmasq

Edit hostapd config file

Now modify the file /etc/hostapd/hostapd.conf to configure hostapd. Modify the contents to the following:

interface=wlan0
driver=nl80211
ssid=MyLittlePony
hw_mode=g
channel=7
wmm_enabled=0
macaddr_acl=0
auth_algs=1
ignore_broadcast_ssid=0
wpa=2
wpa_passphrase=AardvarkBadgerHedgehog
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
rsn_pairwise=CCMP

Note values for hw_mode are:

• a = IEEE 802.11a (5 GHz)
• b = IEEE 802.11b (2.4 GHz)
• g = IEEE 802.11g (2.4 GHz)

Specify location of hostapd file

Modify the file /etc/default/hostapd to read:

DAEMON_CONF="/etc/hostapd/hostapd.conf"

Restart hostapd

sudo systemctl unmask hostapd
sudo systemctl enable hostapd
sudo systemctl start hostapd

Check status and ensure running ok:

sudo systemctl status hostapd
sudo systemctl status dnsmasq

Troubleshooting

If something fails it will probably be on the start step:

$ sudo systemctl start hostapd
Job for hostapd.service failed because the control process exited with error code.
See "systemctl status hostapd.service" and "journalctl -xe" for details.

Link is not ready/Driver initialization failed

Here is the problem I encountered at first:

https://askubuntu.com/questions/472794/hostapd-error-nl80211-could-not-configure-driver-mode/743127#743127

#!/bin/sh

IFACE="wlan1"
echo "Starting hostapd with interface $INAME"
/bin/sleep 5
echo "Go time"
/usr/sbin/service hostapd stop
/usr/sbin/service network-manager stop
/usr/sbin/ifconfig $IFACE down
/usr/sbin/rfkill unblock wlan
/usr/bin/nmcli radio wifi off
echo "Stopping/starting hostapd service"
/usr/sbin/service hostapd stop
/bin/sleep 2
/usr/sbin/service hostapd start

Cannot open PID file

Another error I encountered was hostapd not being able to open PID file:

Packet received on interface that has no address

Problem with error message "DHCP packet received on wlan1 which has no address":

Underlying issue was with DHCP not working. I was able to see the wifi AP being broadcast, and try to connect to it, but was failing to get assigned an IP address. This was an indication the problem was with the DHCP service.

Turns out, it wasn't running. To start the DHCP service:

service dhcpcd restart

Strategy for Debugging

In one window, run this command to run hostapd in the foreground:

hostapd -d /etc/hostapd/hostapd.conf

In another window, monitor the system log:

tail -f /var/log/syslog

Now try connecting to the wifi access point that you created. This should generate some useful/interesting events in the log.